Estimates Trouble Codes P2096

P2096: Post Catalyst Fuel Trim System Too Lean (Bank 1)

Our mobile mechanics can quickly diagnose a P2096 trouble code and bring the shop to you 7 days a week. Get a quick and fair quote today.

Find Your Cost

(2,074 Reviews)

What is P2096?

The P2096 code is a Diagnostic Trouble Code defined as “Post Catalyst Fuel Trim System Too Lean (Bank 1)”. It indicates that your car’s Powertrain Control Module (PCM) perceives a lean mixture downstream of the catalytic converter in the exhaust system.

In “V” configuration engines (like a V6 or V8), Bank 1 refers to the oxygen sensor on the side with cylinder #1. Inline engines only have one bank.

There’s a heated oxygen sensor positioned before and after the catalytic converter.

One oxygen sensor (the upstream O2 sensor, front O2 sensor, or AF sensor) sits between the engine and the catalytic converter. The one located after the converter is called the downstream O2 sensor (or rear sensor) and evaluates the oxygen levels coming out of the converter.

The Powertrain Control Module uses the downstream sensor to evaluate the O2 levels coming out of the converter. This helps it keep track of the air fuel ratio burned by the engine.

Higher levels of oxygen in the exhaust tell the PCM that the engine is burning a lean mixture. Conversely, lower oxygen content suggests a rich mix.

Common symptoms

As with any other Diagnostic Trouble Code, one of the most common symptoms of the P2096 post catalyst fuel code is the Check Engine Light turning on. However, other symptoms can turn up depending on the specific part or system responsible for the issue in the fuel trim.

Here’s a more detailed list of common symptoms:

  • Illuminated engine light
  • Rough idle
  • Bad fuel economy
  • Poor acceleration
  • Engine misfires

Can I still drive?

Code P2096 is a relatively serious trouble code. So while you can keep driving, prolonged exposure to improper fuel mixture can damage important car parts.

Therefore, it’s usually advised to contact a mechanic as soon as you see the Check Engine Light or encounter the P2096 post catalyst fuel code.

P2096 causes

A number of reasons can cause the lean air fuel ratio that triggers the fault code P2096.

Here are some of the most frequent causes of DTC P2096:

  • Your fuel pressure regulator is not working.
  • There’s low fuel pressure caused by a clogged fuel filter, failing fuel pump, failed fuel pressure regulator, or clogged or leaking injectors.
  • Your mass airflow sensor (MAF sensor) is defective and unable to detect the mass air flow.
  • Your catalytic converter is clogged.
  • A vacuum leak or exhaust leak in the engine causes unmetered air to enter the intake manifold — resulting in an overly lean mixture.
  • The exhaust manifold is cracked or rusting.
  • The oxygen sensor or its circuit is malfunctioning.


Resolving DTC P2096 requires careful attention. In most cases, your mechanic will conduct the following diagnosis to clear the code:

  1. Start by connecting your car to an OBD-II scanning tool. Capture the freeze frame data and check for other error code triggers.
  2. While the car is running, look under it for the catalytic converter. If it is glowing red, this likely means it’s clogged.
  3. Inspect the vacuum lines, wiring harness, and exhaust system. Check for any cracked or damaged hoses and make sure there’s no exhaust leak, vacuum leak, or a leak in the gasket.
  4. Next, examine the electrical connector (or harness connector) for the O2 sensor and mass air flow (MAF sensor). Check the wiring for damage or disconnects.
  5. Test the downstream oxygen sensor (rear sensor) with a digital multimeter. Check to see if it’s faulty or shorted, and replace it.

Possible repairs for P2096 & Costs

Once you identify the root cause of error code P2096, it becomes easier to conduct the right repairs. 

DTC P2096 is often caused by a combination of one or more problems, so your mechanic may implement any of the following fixes to clear the trouble code:

  • Repair the vacuum hose or other hose/line leak
  • Repair any cracks, missing gasket, rust holes
  • Replace the fuel filter, fuel pump, or fuel pressure regulator
  • Replace the spark plugs
  • Replace the downstream O2 sensor
  • Replace the oxygen or mass airflow sensor (MAF sensor)
  • Catalytic converter replacement (rare)

Since fault code P2096 doesn’t have a single fixed solution, its costs vary depending on the severity of the trouble code. In general, you should expect to pay anywhere from $400-$500, including the cost of parts and labor.

However, in the rare case when you have a faulty catalytic converter, repair costs can go as high as $3000 for catalytic converter replacement.

How It Works

Tell us about your vehicle

Select your vehicles year, make, and model and the repair service you need.

Book online

Get a free quote, book an appointment, and speak to a specialist – all online!

Schedule your repair

Pick a time that works best for you and our mobile mechanics will bring the shop to you.

Get a Quote

certified 12-Month | 12,000-Mile Warranty

We're here to keep you moving

Our experienced mobile mechanics are ready to help.

Get a Quote

1-Year | 12,000-Mile Warranty